![]() This hardware output design is also shared by many 3rd party audio interface / controllers as you will find them among TRAKTOR READY devices. Examples of such an audio interface are TRAKTOR KONTROL S4 and TRAKTOR KONTROL Z1. In almost every scenario, TRAKTOR's Master output will be routed to the RCA output while the Monitor output will be routed to the jack output. ![]() Below we explain important aspects to consider when optimizing TRAKTOR for best results in internal mixing mode: Audio InterfaceĪn internal mixing setup requires an audio interface equipped with two (stereo) output channels, whereby typically (but not exclusively) one of the physical output channels is of the type RCA stereo (left and right outputs) and another one is of the type minijack or jack 1/4''. In internal mixing mode, the digital audio signal from each Deck is processed and controlled entirely by TRAKTOR's software mixer. In the example below, the TRAKTOR KONTROL Z1 audio interface is routed for these two output channels in internal mixing mode. It is usually connected physically to a pair of headphones and activated by pressing on the Cue (headphones) button of the corresponding Deck in the software mixer. ![]() Output Monitor: This is your pre-listening (cue) signal.The Master output signal is usually connected physically to your speakers or to an input channel (line level) of a club mixer for example via the built-in jack output of your PC or the MAIN RCA (left and right) output of a TRAKTOR KONTROL device. Output Master: This output signal is the sum of any of the four Decks and/or Loop Recorder playing at any time.In internal mixing mode, the TRAKTOR software offers two separate audio outputs: TRAKTOR allows you to configure the software for internal mixing mode by selecting it under Mixing Mode in TRAKTOR Preferences > Output Routing. ![]() In the next chapters we will explain how to handle your output levels depending on the type of mixing mode being used. It is very important to set your individual gain controls so that the level peaks still reach the orange area of the MAIN level meter (headroom range).īut never reach the red area (clipping occurs). The main output level of TRAKTOR (sum of all playing Decks / Loop Recorder) is indicated visually by the MAIN level meter on the top of TRAKTOR's main screen. The signal levels of the individual mixer channels are indicated by the blue level meter on their volume faders. The gain control is used to match the levels of your tracks. It is important to keep an eye on the gain value in order to avoid clipping. Setting Gain LevelsĮach channel of TRAKTOR's software mixer has a GAIN control which increases the level of the audio signal coming from the corresponding Deck. In chapters 2 and 3 we will explain how to set the Limiter in TRAKTOR to attain the best possible quality in sound. The use of a limiter avoids digital clipping at the cost of a loss in dynamic range. LimiterĪ limiter attenuates the signal peaks exceeding a pre-defined level. In the next sections we will explain how to set these parameters to avoid digital clipping. In digital audio processing in TRAKTOR, every component of the software mixer contributes to a reduction of the headroom level before clipping occurs. Therefore, please be aware that using and / or adding EQ, additional Decks and effects in TRAKTOR can faster lead to an overdrive of the main output signal above the headroom level. Whereas analog clipping allows for greater increase in output levels without damaging the original signal significantly, digital (software-based) clipping will overdrive the signal more noticeably. ClippingĪudio clipping is an unwanted distortion which occurs when the audio signal is overdriven beyond the capabilities of the audio system (i.e. TRAKTOR's software mixer allows you to define its own headroom settings which will be explained in chapters 2, 3, and 4. The amount of headroom thus allows a DJ to exceed the reference level when performing live while remaining within a safety range where clipping does not occur. In both digital and analog signal processing, headroom is defined as the amount by which the reference level of an audio mixer can be exceeded before the signal degrades or distorts (known as 'clipping', see below). This has important implications regarding the handling of output levels (channel volume fader, channel gain and main output). The article is divided into 4 chapters:Īs opposed to analog mixing, DJ software mixes audio signals digitally. This article offers information on how to configure TRAKTOR and set output levels to achieve the best possible sound quality during audio playback.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |